Zirconium Alloy Sheet Supplier: Flatness, Surface and RFQ
- Zirconium Alloy Sheet Supplier

A zirconium alloy sheet supplier should confirm the offered gauge, flatness, surface and edge requirements for the intended fabrication. Use a sheet-specific RFQ so quotations describe comparable material and inspection.
1. Selection and Acceptance Decisions
- Provide the sheet size, gauge tolerance, flatness method and protected-face requirements.
- State the intended forming, lining or welding operation and request the delivery condition suited to the agreed process.
- Confirm cut edges, marking, packaging and lot documentation, including how transit damage will be assessed at receipt.
Send a specification for this material with the grade, dimensions, quantity, intended use and the acceptance details listed above. Ask for confirmation of the quoted size, condition and documentation.
2. Sheet vs Plate: Why the Distinction Matters
ASTM B551 covers strip, sheet and plate as separate product forms with different tolerance tables: strip is the thin band (under ~4.75 mm), sheet the middle band, and plate the thick band (≈ 6.35 mm and over per standard practice). Suppliers run the same alloy through different processes per band — strip/sheet on cold-rolling and leveling routes, plate on hot rolling — so naming the correct form on the RFQ is the first accuracy check.
The Sheet-Specific Checklist
- Gauge and profile — nominal thickness plus the tolerance band, and ask for across-width thickness profile data, not an average;
- Flatness — leveling practice and the flatness standard the supplier can hold for the width;
- Surface — pickled (scale-free, uniform) or bright; state Ra where the sheet is a finished surface;
- Edge condition — slit or sheared, with burr limits for automated forming;
- Condition — annealed for forming; confirm the tensile values match the ordered gauge band.
3. Grades for Sheet
Grade | UNS | Tensile (min) | Elongation (min) | Typical sheet duty |
Zr702 | R60702 | ≥ 379 MPa | 16% | Acid liners, trays, formed seals |
Zr705 | R60705 | ≥ 552 MPa | 16% | Higher-stress corrosion parts |
Zr704 | R60704 | ≥ 413 MPa | 14% | High-temperature corrosion service |
Table 1 — Annealed minimums per ASTM B551 for zirconium sheet grades.
4. Ordering Sheet
Write: grade + UNS; form (“sheet”); thickness with tolerance band; width and length; surface and edge; condition; standard + edition; documentation. For formed liners and trays, annealed condition and flatness are the fields that prevent shop-floor surprises. Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.
FAQ
(1) What is the difference between zirconium sheet and plate?
Thickness band and tolerance regime: sheet is the thin-to-mid band fabricated by cold rolling and leveling, plate the thick band from hot rolling. ASTM B551 tables differ by form, so name the correct form on the order.
(2) Which grade should I order for hydrochloric-acid service?
Zr702 (UNS R60702) is the standard commercial-pure choice for HCl and reducing-acid duty; Zr705 adds strength where the part is stressed; Zr704 suits higher-temperature corrosion service.
(3) How flat can zirconium sheet be supplied?
Flatness depends on width, gauge and the leveling line; ask for the supplier’s flatness standard and state your requirement rather than assuming a generic value.
(4) Is zirconium sheet weldable?
Yes — TIG or electron-beam under inert-gas shielding, with clean, oxide-free joint preparation; hydrogen discipline decides weld quality.
(5) What documents should accompany sheet?
MTR with heat number, full chemistry including O/N/H, tensile for the gauge band, condition and standard edition, plus thickness profile and flatness data where agreed. Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.
Related Resources and Inquiry
See the zirconium plate category or send your specification.
Baoji Titanium Valley Titanium Nickel Zirconium Material Processing Co., Ltd. produces zirconium foil, strip, sheet and plate per ASTM B551/B551M (R60702 / R60705) from vacuum-melted ingots on a 750 mm 20-high precision rolling line under ISO 9001 / ISO 13485. Send your specification to sales@titaniumvalleys.com — Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.
5. Related Reading
- Zirconium 702 Sheet: Flatness and Forming Acceptance
- Zirconium Alloy Plate Supplier: Supply Scope and Inspection
References
1. ASTM B551/B551M, Standard Specification for Zirconium and Zirconium Alloy Strip, Sheet, and Plate.
2. ASTM E8/E8M, Standard Test Methods for Tension Testing of Metallic Materials.
3. GB/T 21183, Zirconium and Zirconium Alloy Sheet, Strip and Foil.
This article is a technical reference. It does not constitute a commercial offer; dimensions, tolerances and documentation are confirmed at order review.
Published by: Titanium Valley Technical Team. Technical and quality review: pending.