Zirconium Alloy Sheets: Grade and Condition Selection
- Zirconium Alloy Sheets

Zirconium sheet grade selection should connect composition and required strength with fabrication and service conditions. Review each proposed grade against the governing product specification and the supplier’s actual offer.
1. Selection and Acceptance Decisions
- Confirm material identity and the required mechanical condition before comparing grade tables.
- Review the process medium and fabrication route for each candidate instead of assuming that every zirconium grade has identical corrosion behavior.
- Ask the supplier to confirm availability and acceptance requirements for the selected grade, gauge and sheet dimensions.
Send a specification for this material with the grade, dimensions, quantity, intended use and the acceptance details listed above. Ask for confirmation of the quoted size, condition and documentation.
2. The Grade Ladder
Grade | UNS | Alloying | Tensile (min) | Elongation (min) | Position |
Zr702 | R60702 | None (Zr+Hf ≥ 99.2%) | ≥ 379 MPa | 16% | General reducing-acid service |
Zr704 | R60704 | Sn 1.2–1.7, Fe 0.18–0.24, Cr 0.07–0.13 | ≥ 413 MPa | 14% | High-temperature corrosion |
Zr705 | R60705 | Nb 2.0–3.0 | ≥ 552 MPa | 16% | Stressed acid parts |
Table 1 — Annealed minimums per ASTM B551 for the zirconium sheet grades.
3. Selection Logic
Start with corrosion: all three carry the ZrO₂ passive film, so the reducing-acid window (non-fluoride HCl, sulfuric, organic and mixed acids) is common to the family — the grade choice does not fix corrosion. Then look at load and temperature: Zr702 for general liners and formed parts; Zr705 where the sheet carries stress (roughly 45% more tensile); Zr704 where the service runs hot and creep becomes the design driver. When in doubt, the cheaper Zr702 with a thicker section often wins on total cost.
Common Service Boundaries
- Strong — hydrochloric acid across wide windows, dilute-to-mid sulfuric, organic acids, mixed non-fluoride acid systems;
- Attacked — hydrofluoric acid and fluoride-containing media;
- Case-by-case — strongly oxidizing acidic mixtures and hot concentrated sulfuric (follow iso-corrosion data).
4. Ordering Alloy Sheets
Name the grade + UNS; form (sheet); thickness with tolerance band; width, length, flatness class; surface and edge; condition; standard + edition; documentation. The grade designation alone is not enough — the standard edition pins the chemistry and tensile the mill must meet. Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.
FAQ
(1) Which zirconium sheet grade is most corrosion resistant?
All three share the same ZrO₂-based corrosion window; the grades differ in strength and temperature capability, not corrosion. Match the grade to load and heat.
(2) What is Zr704 used for?
Zr-Sn-Fe-Cr sheet for high-temperature corrosion service where strength retention and creep matter more than ultimate tensile.
(3) Can the grades be welded together?
Yes — the family welds across grades with TIG or electron-beam under inert-gas shielding; confirm filler and procedure for mixed-grade joints.
(4) Is zirconium alloy sheet magnetic?
No — the family is non-magnetic, which suits instrument and MRI-adjacent components.
(5) How do I choose between Zr705 and thicker Zr702?
Compare cost: Zr705’s +45% tensile often substitutes for a thicker Zr702 section, but the premium must beat the extra metal cost. Run both quotes at equal load capacity. Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.
Related Resources and Inquiry
See the zirconium plate category or send your specification for an alloy-sheet review.
Baoji Titanium Valley Titanium Nickel Zirconium Material Processing Co., Ltd. produces zirconium foil, strip, sheet and plate per ASTM B551/B551M (R60702 / R60705) from vacuum-melted ingots on a 750 mm 20-high precision rolling line under ISO 9001 / ISO 13485. Send your specification to sales@titaniumvalleys.com — Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.
5. Related Reading
- Zirconium 702 Sheet: Flatness and Forming Acceptance
- Zirconium 705 Plate: Comparing Strength and Fabrication Needs
References
1. ASTM B551/B551M, Standard Specification for Zirconium and Zirconium Alloy Strip, Sheet, and Plate.
2. ASTM E8/E8M, Standard Test Methods for Tension Testing of Metallic Materials.
3. GB/T 21183, Zirconium and Zirconium Alloy Sheet, Strip and Foil.
This article is a technical reference. It does not constitute a commercial offer; dimensions, tolerances and documentation are confirmed at order review.
Published by: Titanium Valley Technical Team. Technical and quality review: pending.