Titanium Rod 2.5 mm: Straight Stock and Coil Requirements

Titanium Rod 2.5 mm

This guide covers titanium rod 2.5 mm in nominal diameter. A request written only as titanium rod 2.5 leaves the unit and supply form unclear, so specify millimeters and whether the material is needed as straight stock or coil.

1. Selection and Acceptance Decisions

  • Give the required cut length and straightness method for pins, shafts or other small parts.
  • For coil supply, specify the relevant wire condition, coil format and intended straightening or forming operation.
  • Confirm the actual product standard and dimensional acceptance with the supplier instead of selecting a standard by diameter alone.

Send a specification for this material with the grade, dimensions, quantity, intended use and the acceptance details listed above. Ask for confirmation of the quoted size, condition and documentation.

2. Rod or Wire: The 2.5 mm Boundary Question

Commerce treats small diameters flexibly: straight, cut-to-length 2.5 mm product is sold as rod, while the same diameter on a spool or coil is wire. ASTM B863 is the wire specification and ASTM B348 the bar specification; both list the same chemistry families, and the practical difference is form, straightness and packaging. State the product form explicitly — it changes tolerance practice, packaging and price.

3. Grades for 2.5 mm Rod

Grade

Tensile (min, annealed)

Elongation (min)

Typical use at 2.5 mm

Grade 1

≥ 240 MPa

24%

Forming, medical, low-stress parts

Grade 2

≥ 345 MPa

20%

Pins, shafts, corrosion service

Grade 5

≥ 895 MPa

10%

High-strength pins, springs, fasteners

Table 1 — Annealed minimums (ASTM B863/B348 basis) and what 2.5 mm stock is usually bought for.

4. Tolerances and Straightness

For precision work, specify the diameter tolerance explicitly — ±0.05 mm is common commercial practice and ±0.01 mm is achievable for fine straight product — and a straightness target such as ≤1 mm/1, 000 mm. The tolerance class (h9/h10) only means something when tied to the diameter and production route, so quote them together.

Applications

  • Precision pins and shafts — instrument and mechanism parts machined from straight rod;
  • Electrodes and anodes — Grade 1/2 rod for electrochemical cells and plating fixtures;
  • Medical components — guide-wire-class and instrument stock ordered to ASTM F67/F136 where implants are involved;
  • Fastener blanks — Grade 5 2.5 mm rod headed into miniature titanium screws;
  • Hobby, jewelry and research — the retail-size rod that most small-quantity buyers order.

5. How to Order 2.5 mm Titanium Rod

Name: grade + UNS; diameter 2.5 mm with tolerance; product form (straight rod, cut lengths, or coil); condition (annealed or cold-worked); surface (bright, pickled); quantity; standard and edition; documentation. For diameters this small the form and tolerance fields decide whether you receive machinable rod or coil wire. Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.

FAQ

(1) Is 2.5 mm titanium rod the same as titanium wire?

The material is the same; the product form differs. Straight cut-to-length product is rod, spooled product is wire — name the form on the order and the supplier ships the right packaging and tolerance practice.

(2) What is the standard tolerance for 2.5 mm rod?

±0.05 mm is common commercial practice; ±0.01 mm is available for precision work. Confirm the tolerance band together with the production route in the contract. Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.

(3) Can I get Grade 5 at 2.5 mm diameter?

Yes — Grade 5 (Ti-6Al-4V) at 2.5 mm is standard for high-strength pins and fastener blanks, usually supplied annealed or cold-worked.

(4) Which grade should I choose for a corrosion-service pin?

Grade 2 is the default cost-effective choice in seawater and chloride duty; Grade 12 if the part sits in crevices or reducing-acid service.

(5) What lengths are available?

Random lengths in the 300–3, 000 mm class, or cut-to-length per order; small diameters are also supplied on spools in long continuous lengths.

Related Resources and Inquiry

See the titanium rod category and the wire category to compare forms, or send your specification.

Baoji Titanium Valley Titanium Nickel Zirconium Material Processing Co., Ltd. produces titanium rod and barstock from VAR-melted ingots on a rolling line rated over 20, 000 t/yr, per ASTM B348 / GB/T 2965, with cold-drawn, hot-rolled and forged routes. Send your specification to sales@titaniumvalleys.com — Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.

6. Related Reading

References

1. ASTM B348/B348M, Standard Specification for Titanium and Titanium Alloy Bars and Billets.

2. ASTM B863, Standard Specification for Titanium and Titanium Alloy Wire.

3. ASTM E8/E8M, Standard Test Methods for Tension Testing of Metallic Materials.

This article is a technical reference. It does not constitute a commercial offer; dimensions, tolerances and documentation are confirmed at order review.

Published by: Titanium Valley Technical Team. Technical and quality review: pending.