ASTM B265 Grade 1 Titanium Foil: Specification and RFQ Guide
- Grade 1 titanium foil

A Grade 1 foil RFQ should identify the ASTM B265 edition, delivery condition, thickness and width tolerances, coil or cut-sheet format, surface and edge requirements, and the material test report required for lot acceptance. View related foil specifications.
RFQ checklist for Grade 1 foil
Copy into your inquiry: ASTM B265 [edition], Grade 1, [condition], [thickness and tolerance] × [width and tolerance], [coil or sheet], [finish and edge], [quantity], [lot traceability and required MTR data]. Confirm the acceptance method for the ordered gauge.
What ASTM B265 Covers
ASTM B265 — Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate — covers more than 30 titanium grades across three product forms: strip (under 4.75 mm thick), sheet and plate. Grade 1 is one of the commercially pure grades it defines, alongside Grades 2, 3 and 4 and the alloy grades. The “M” suffix (B265M) is the metric companion document; both carry the same technical intent, and the order should always name the contracted edition.
Grade 1 Requirements Inside the Standard
Requirement | ASTM B265 Grade 1 |
Nitrogen (max) | 0.03% |
Carbon (max) | 0.08% |
Hydrogen (max) | 0.015% |
Iron (max) | 0.20% |
Oxygen (max) | 0.18% |
Tensile strength (min) | ≥ 240 MPa |
Yield strength | 170–310 MPa |
Elongation (min) | 24% |
Table 1 — Grade 1 chemistry and annealed tensile requirements per ASTM B265.
One detail trips up new buyers: elongation minimums are specified by thickness band, so the headline 24% applies to the standard gauge bands, and ultra-thin foil bands carry their own values. The yield strength is quoted as a range, not a minimum, because the standard expects values inside 170–310 MPa.
The Three Thickness Bands and Their Tolerances
Commercially supplied Grade 1 foil spans 0.02–1.0 mm in three bands: 0.02–0.2 mm foil, 0.2–0.5 mm strip and 0.5–1.0 mm sheet. The foil band is rolled to a thickness-tolerance class of ±0.005 mm, while B265’s published tolerance tables apply to the strip/sheet/plate bands they cover. Where an order falls below the covered bands — micro-foil under 0.1 mm, or non-standard widths — the honest quoting practice is “ASTM B265 Grade 1 as the material basis, plus a purchase specification for gauge, tolerance and flatness”, which is how professional mills handle ultra-thin foil. Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.
Where B265 Stops: What the Purchase Specification Must Carry
- High-purity variants — 4N–5N titanium for sputtering targets and getters falls outside B265’s chemistry tables and is fixed entirely in the purchase specification (melting route, grain size < 50 µm, surface class);
- Anodizing and coatings — AMS 2487 color or AMS 2488 bond-prep anodizing is downstream processing, never a B265 delivery state;
- Edge condition and burr limits for medical and electronics slitting;
- Interleaving, packaging and cleanliness level for bonding and lamination duty.
Why Buyers Cite B265 Grade 1: Application Snapshot per Band
Application | Typical thickness | Process | Key requirement |
X-ray transmission windows | 0.03–0.06 mm | Precision rolling to gas-tight ultra-thin foil | Strength + gas-tightness, low absorption of soft X-rays |
Li-ion battery current collectors | 0.02–0.03 mm | Precision rolling to the thinnest band | Electrolyte corrosion resistance, mechanical strength, light weight |
EMI shielding foil | 0.05–0.1 mm | Slitting / etching / stamping | Non-magnetic, low density, corrosion resistance |
Coin-cell cases and lids | 0.2–0.3 mm | Multi-station progressive stamping + crimping | Non-magnetic, corrosion-resistant, hermetic sealing |
Pacemaker / defibrillator housings | 0.2–0.4 mm | Deep drawing + laser seal welding | Biocompatibility, EMI shielding, hermetic closure |
Heat-exchanger thin-wall tubes and plates | 0.2–0.5 mm | Roll-welded thin-wall tube from strip | Chloride-ion resistance, good heat transfer |
Table 2 — Representative Grade 1 applications per thickness band (see the Grade 1 application article for the full map).
RFQ Checklist for ASTM B265 Grade 1 Foil
- Grade and UNS — Grade 1 / UNS R50250, standard ASTM B265 (or B265M) with edition and year;
- Dimensions — thickness nominal ± tolerance, width, length or coil ID/OD and coil weight;
- Condition — annealed (M) or cold-worked (Y);
- Surface — bright or matte, cleanliness/dyne level, edge condition;
- Quantity and documentation — weight, MTR to EN 10204 3.1/3.2, RoHS, ISO 9001/13485 certificates;
- Supplementary requirements — any S-type extras from B265, or customer-specific tests.
Verifying the MTR in Practice
Check five fields: heat number; full chemistry including O, N and H; tensile and elongation against the correct thickness band; delivery condition; and the standard edition plus supplementary requirements. A certificate that quotes only tensile strength, or omits interstitial chemistry, is not a complete B265 Grade 1 certificate for foil.
FAQ
(1) Does ASTM B265 cover titanium foil thinner than 0.1 mm?
B265 governs the material — chemistry and tensile requirements apply at any gauge — but its dimensional tolerance tables are defined for product bands that do not extend to every foil gauge. Thin-gauge dimensions are therefore fixed in the purchase specification on a B265 basis. Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.
(2) What is the difference between ASTM B265 and ASTM B265M?
They are the same specification in inch-pound and SI metric versions respectively. Quote the one your QMS and drawings use, and always name the edition year.
(3) What is the difference between B265 Grade 1 and ASTM F67 Grade 1?
F67 is the surgical-implant specification for unalloyed titanium; its composition and property requirements are aligned with but not identical to B265, and it adds implant-specific requirements. Medical orders should cite F67.
(4) What tolerance should I expect for 0.02–0.2 mm Grade 1 foil?
The foil band is produced to a ±0.005 mm thickness-tolerance class; tighter, wider or flatter combinations are quoted as purchase-specification items. Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.
(5) Do I need supplementary requirements when ordering Grade 1 foil?
Not by default, but consider them when the foil is bonded, coated, anodized, etched or used at elevated temperature — typical extras cover surface cleanliness, interleaving, packaging and additional testing.
(6) Where does anodizing fit into a B265 order?
Specify the required anodic process and acceptance criteria with the processor. Use an approved appearance sample for decorative color and qualify the surface preparation for bonded assemblies.
(7) How do high-purity sputtering-target foils relate to B265?
They do not sit inside B265: 4N–5N purity, melting route and grain-size targets are purchase-specification items. B265 Grade 1 remains the reference for standard-purity foil forms.
(8) Which thickness band should I name in the MTR request?
Always name the band with the elongation value — tensile and elongation requirements differ by band, and quoting a number without its band is a common certificate-reading error.
Related Resources and Inquiry
For the full grade ladder see the ASTM B265 scope and grade selection guide, or start with the Grade 1 titanium foil product page. Send your specification to open an order review.
Titanium Valley quotes ASTM B265 Grade 1 titanium foil across 0.02–1.0 mm from a 750 mm 20-high line under ISO 9001 / ISO 13485. Send your specification to sales@titaniumvalleys.com — Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.
References
1. ASTM B265, Standard Specification for Titanium and Titanium Alloy Strip, Sheet, and Plate.
2. ASTM F67, Standard Specification for Unalloyed Titanium, for Surgical Implant Applications.
3. ASTM E8/E8M, Standard Test Methods for Tension Testing of Metallic Materials.
4. Baoji Titanium Valley: 0.02–1.0 mm Titanium and Titanium Alloy Strip and Foil — Application Introduction (internal application deck).
5. EN 10204, Metallic Products — Types of Inspection Documents.
6. Titanium Valley product data: Gr1 Titanium Foil product page (titaniumvalleys.com).
This article is a technical reference. It does not constitute a commercial offer; dimensions, tolerances and documentation are confirmed at order review.
Published by: Titanium Valley Technical Team. Technical and quality review: pending.