Zirconium 702 Sheet vs Plate: Form and Order Comparison
- Zirconium 702 Plate

Zirconium 702 sheet and plate should be ordered using the form and tolerance definitions in the applicable specification and supplier offer. Decide the fabrication requirement first, then confirm which form and acceptance rules apply.
1. Selection and Acceptance Decisions
- State the thickness, width and length and ask the supplier to identify the quoted product form.
- Compare flatness, surface, edge and dimensional requirements separately for sheet and plate in a mixed order.
- Keep heat or lot identification and the relevant inspection results attached to each supplied item.
Send a specification for this material with the grade, dimensions, quantity, intended use and the acceptance details listed above. Ask for confirmation of the quoted size, condition and documentation.
2. The Two Forms
Form | Thickness band (B551 practice) | Route | Typical duty |
Sheet | Thin-to-mid band (under ≈ 4.75 mm) | Cold rolling + leveling | Liners, trays, formed parts |
Plate | Thick band (≈ 6.35 mm and over) | Hot rolling + finishing | Vessels, tube sheets, structure |
Table 1 — Sheet and plate as separate product forms with separate tolerance tables.
3. Chemistry and Properties (Both Forms)
Item | Value |
Zr + Hf | ≥ 99.2% (Hf ≤ 4.5%) |
Tensile strength (min, annealed) | ≥ 379 MPa (55 ksi) |
Yield strength (min) | ≥ 207 MPa (30 ksi) |
Elongation (min) | 16% |
Density | 6.51 g/cm³ |
Table 2 — Zr702 requirements per ASTM B551, common to sheet and plate.
4. Surfaces and Edge Conditions
Both forms ship pickled (scale-free, uniform) or with machined surfaces where flatness and Ra matter. Sheet is slit or sheared — specify burr limits for automated forming; plate edges are sheared or machined per the fabrication plan. State the surface you will weld or form against: it changes joint preparation and finishing cost.
Ordering Checklist
- Grade + UNS (Zr702 / R60702);
- Form — sheet or plate, named explicitly;
- Thickness with tolerance band, width, length;
- Surface and edge condition;
- Condition — annealed;
- Standard + edition — ASTM B551/B551M (ASME SB-551 practice for pressure equipment);
- Documentation — MTR, UT report for heavy plate, EN 10204 3.1/3.2 class.
FAQ
(1) Should I order sheet or plate for a vessel lining?
Sheet for the liner itself (formed, lighter gauges), plate for the load-bearing shell and tube sheets. The two forms carry different B551 tolerance tables, so name the form per drawing.
(2) Can sheets and plates be mixed in one order?
Yes — state each item with its own form, gauge band and tolerance; a single “Zr702 plates & sheets” line without itemization invites tolerance disputes.
(3) What is the lead time difference between sheet and plate?
Sheet is typically faster (cold-rolling routes, common gauges); thick plate is hot-rolled to order and takes longer, especially with UT and third-party requirements.
(4) Is Zr702 sheet weldable to Zr702 plate?
Yes — identical chemistry welds cleanly with TIG or electron-beam under inert-gas shielding.
(5) Which documents should each form carry?
MTR with full chemistry including O/N/H, tensile for the correct gauge band, condition and standard edition; add UT for heavy plate and EN 10204 3.2 where codes require. Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.
Related Resources and Inquiry
See the zirconium plate category or send your specification.
Baoji Titanium Valley Titanium Nickel Zirconium Material Processing Co., Ltd. produces zirconium foil, strip, sheet and plate per ASTM B551/B551M (R60702 / R60705) from vacuum-melted ingots on a 750 mm 20-high precision rolling line under ISO 9001 / ISO 13485. Send your specification to sales@titaniumvalleys.com — Custom size, condition, tolerance and documentation can be reviewed to the purchase specification.
5. Related Reading
- Zirconium 702 Plate: Service Review and Fabrication
- Zirconium 702 Sheet: Flatness and Forming Acceptance
References
1. ASTM B551/B551M, Standard Specification for Zirconium and Zirconium Alloy Strip, Sheet, and Plate.
2. ASTM E8/E8M, Standard Test Methods for Tension Testing of Metallic Materials.
3. EN 10204, Metallic Products — Types of Inspection Documents.
This article is a technical reference. It does not constitute a commercial offer; dimensions, tolerances and documentation are confirmed at order review.
Published by: Titanium Valley Technical Team. Technical and quality review: pending.